Please note that new user registrations disabled at this time.

Bug with Khelgar (possible spoiler)

This forum is to be used for all discussions pertaining to Obsidian Entertainment's Neverwinter Nights 2, the Mask of the Betrayer expansion pack, the Storm of Zehir expansion pack, and the Mysteries of Westgate adventure pack.
Post Reply
User avatar
Rockdomchick
Posts: 15
Joined: Tue Oct 31, 2006 4:51 pm
Location: Burton on Trent, UK
Contact:

Bug with Khelgar (possible spoiler)

Post by Rockdomchick »

Hello, I've tried searching for this but I couldn't find anything relating to this so I'm sorry if it's being covered elsewhere.

Basically I've just had the Keep given to me and am off on quests. The problem is that if I have Khelgar the dwarf in my party, he just stands there unless I control him. He doesn't move or get involved in fights. I've checked the behaviour section and he is in exactly the same modes as everyone else in my party. I'm also patched up to the the latest one. I've tried removing and re-adding him and also restarting/reloading from earlier saves but nothing helps. I've not had this problem with any other member.

Any ideas?

:confused:
User avatar
Cyrinn
Posts: 174
Joined: Fri Feb 09, 2007 3:27 pm
Contact:

Post by Cyrinn »

Ewww, sounds like an odd bug. There are a few for him, one where he turns into a cat lol (okay, he gets stuck in Sand's familiar..) But i could not find this one and you are sure his behavior is NOT on puppet mode?

What version are you using? I have had no probs with 1.03, but 1.04 apparently has a few new ones.
User avatar
Rockdomchick
Posts: 15
Joined: Tue Oct 31, 2006 4:51 pm
Location: Burton on Trent, UK
Contact:

Post by Rockdomchick »

Am positive his behaviour is not on puppet mode, I've altered it to puppet mode and back again and I've selected the "All" option too to make sure that it is not selected but he still won't move.

I'm on the 1.04 version, mind you I've just updated with a new patch now (found after I posted here! :rolleyes: ) so I'll have a go with him again and see if it helps, and will report back.
But thanks for your reply :)
User avatar
swcarter
Posts: 3274
Joined: Mon Nov 17, 2003 12:00 pm
Location: California
Contact:

Post by swcarter »

It's possible that he thinks he's supposed to be standing his ground. That happens sometimes after cutscenes. So try right clicking somewhere and holding the right mouse button down. A menu should pop up that includes broadcast commands. Select "follow me" (or whatever it's called) and see if that works.

SWC
Sir Edmund: "Should you obey the lord who asks you to put a village of innocents to the torch? Is that chivalrous? Is it noble?"
Me: "It's a great way to get promoted, I know that much."
User avatar
Rockdomchick
Posts: 15
Joined: Tue Oct 31, 2006 4:51 pm
Location: Burton on Trent, UK
Contact:

Post by Rockdomchick »

I've tried him with the latest patch (updated this morning) and he still doesn't want to move :mad:

SW: thats one thing I've not tried... thanks for the suggestion, I'll try it out :)
User avatar
Cyrinn
Posts: 174
Joined: Fri Feb 09, 2007 3:27 pm
Contact:

Post by Cyrinn »

swcarter wrote:It's possible that he thinks he's supposed to be standing his ground. That happens sometimes after cutscenes. So try right clicking somewhere and holding the right mouse button down. A menu should pop up that includes broadcast commands. Select "follow me" (or whatever it's called) and see if that works.

SWC
Haha, that's weird, never had that problem. Might want to revert back to 1.03 if the command isn't whats doing it. Unless, of course, that version had the same problem.

I have had very few probs with 1.03, and am very hesitant to update to 1.04, since new bugs keep popping up with it...and it is stuff that was fine before. Hopefully they get it right with 1.05..
User avatar
pwcook
Posts: 44
Joined: Fri Sep 05, 2008 7:27 pm
Location: Edmonton, AB, CANADA
Contact:

Post by pwcook »

I had a similar problem except my whole party just stood there. Quite frustrating. Tried SW's suggestion and it seems to be working now. Thanks
Post Reply